#Unifi not showing wired client activity drivers#
#Unifi not showing wired client activity Patch#
#Unifi not showing wired client activity pro#
#Unifi not showing wired client activity tv#
#Unifi not showing wired client activity mac#

Kinda annoying when it is the best AP out of them all and I’m getting sub-par issue with it being the newest as well. The only thing I can think of at the moment is something to do with the AP 6’s ethernet port is damaged/not working correctly so it can see the power but the data aspect of the connection is not doing anythingĪnyone got any tips or things I can try?. Theres the Security Gateway sitting upstream of the switch and the activity its both seen and is seeing. Just enabled the UniFi integration for a Dream Machine. More information an asking questions can been found at the Homey Community Topic Supported devices Wifi Client Wired client Flow cards Click on a device above to show related Flow cards only.

#Unifi not showing wired client activity pro#

penright (Paul Enright) December 4, 2019, 4:26pm 1. Homey Pro This app adds support for presence detection based on (wifi) clients connected to the UniFi Controller on your Homey. The eth port shows its connected and counts data but it says device last seen like 2 weeks ago in history.

#Unifi not showing wired client activity tv#

We have a Samsung tv that stopped showing up after installing 1.9.0-12 beta and hasnt worked since with newer betas. For some reason, the unifi integration has two separate settings parts, where I assume I have to configure Track network and track wired network clients, if I am going to be able to hook up presence detection for the. UniFi intergration, why some clients are not showing up as entities. Missing wired client Has anyone had a issue where a lan device is not showing up in wired clients. I have a not been in the roof or climbing around or had any work done in that area or in the roof to damage/disturb the cable (plus there are a bundle of cables running the same length if one was cactus i would assume others were as well) But since unifi seems to find about a hundred new mac-addresses every week, I DONT want to track NEW clients. I am using the POE injector to save my POE switch so i unplugged that and tried to go through the POE switch and still has the same, not using uiplink issue.

#Unifi not showing wired client activity Patch#

I have used a simple cable tester on each of the patch cables and the in wall run which all show as no broken connections, so it’s not that. I have tried to turn off meshing in the AP’s settings however it doesn’t connect via the wired link anymore and just will stay isolated if i do that. When I set up the integration I ticked all three options: Track network clients. I have a new device connected to my unifi wifi, can see it in my unifi app on Wi-fi but it’s not showing up in the unifi integration or in developer tools. I have 2 other UniFi AC Lites working just fine using wired uplinks. I have HA running on pi with the unifi addon. It was working for a while just fine, however as I usually do a periodic check in unifi connect I saw that it was no longer using the wired uplink hence this round of trouble shooting.

#Unifi not showing wired client activity mac#

The igb0 interface mac address is not listed as a client in Unifi (but is connected on Port 12).I seem to have a weird issue in which my UniFi AP 6 Lite used to connect via the wired uplink but now doesn’t and will mesh from another access point.

#Unifi not showing wired client activity drivers#

I originally had thoughts of using LAGG until I learned that you shouldn't mix drivers and its very annoying that the motherboard has two nics of different types. It's link state is up, but has no DHCP, no IPv4 and no IPV6. Not sure if related, but there is also an igb0 interface not used. The Unifi control panel (which is not on a jail or anything, its running on my UDM Pro) is not reporting network traffic to/from my TrueNAS. Activity, Activity Down and Activity Up always show zero bytes.Experience is sold green 100% for both, connection LAN.IP addresses listed are values expected.The mac addresses listed in Unfi for TrueNAS and Jails are values expected.Clients: View all connected wired and wireless clients, and adjust settings for them. All other devices are reporting traffic just fine, only the TrueNAS is not (I have 1 jail for Syncthing, its also showing zero traffic). Devices: View your UDM and any other UniFi devices you have joined to it: Access Points, Switches, etc. When I view the TrueNAS server in list of clients, it shows zero traffic. When I look at Port 11, it shows Rx and Tx status in the hundreds of GB of traffic. All of these are listed as 'N/A'.Įm0 is plugged directly into Port 11 on a USW-Lite-16-PoE switch. I'm not using LAGG, not even VLANS yet.Network > Interfaces > MAC Address matches the mac address listed in the Unifi Controller.Verify that VLAN Switching is enabled under Device Properties.

em0 is up and TrueNAS dashboard shows traffic. If VLAN switching is not enabled, no VLAN will be assigned to an authentication response. I’m not really sure why the controller is behaving that way. So if I blocked wired clients then it would not track my phone. I have a TrueNAS-12.0-U2 up and running fine. For example, yes, you can only track wireless clients but for some reason my Unifi controller is seeing my wifi connected cell phone as a wired client connected to my Unifi Switch.